|
Cutting line compose of lifter jogger and microcomputer program-control paper cutter. It can finish load and unload clean up move of all kinds of paper cutter. It has excellences high efficiency lower intensity of labour short work time debase product cost. Main features: 1. Ball lead screw and linear guide-rail makes paper impeller run smooth,low noise,accurate positioning,enhance the cutting precision and speed greatly,prolong the service lift of paper cutter. 2. The working tables are all chrome-plated and equipped with air balls which makes paper-pushing easily and rusty-proof.Large side workingtable(1000*800) is optional. 3. IR photoelectric protection,buttons by two hands safety devices. 4. Safety device for knife bed, overloading protection for cutting,automatic return safety device. 5. Imported hydraulic components are adopted in hydraulic system,the pressure can be adjusted.The paper is pressed twice by pressure-increased system. 6. mechanical assistance device for knife replacement makes knife replaced quickly and safely. 7. optical knife alignment equipped makes cutting more convenient. 8. chrome-plated working table. 9. PLC control system. 10. ejecting device for knife bar. 11. flat worm speed reducer transmission. 12. inside electronic knife locker to make the cutting more safety and stable. 13. Multination langueage operation interface. 14. Carry on the block programming operation through the figures and diagrams operation manual.
New high speed paper cutter
Product Introduce: This model adopts Japan AC digit servo control system,10.4 inches colorful liquid crystal display screen of resolution rate is 0.01mm, has self-diagnostic function of troubles and displays the operating pattern. It has 100 program units, more than 10000 different cutting position dynamic cutting display, running situation, dynamic follow-up. The max paper-pushing speed is 5-18m/min, it adopts stronger computer operating system. It can memorize store the storage time can be up to 300000 hours above . It has self maintenance to the operating system. Italy hydraulic components, Germany Japan and korea electric components. Taiwan ball lead screw and linear guide-rail are used. PLC controller can monitor all the electrical and mechanical section. Its key parts adopt imported bearing of low maintenance. Main features: 1. Ball lead screw and linear guide-rail makes paper impeller run smooth,low noise,accurate positioning,enhance the cutting precision and speed greatly,prolong the service lift of paper cutter. 2. The working tables are all chrome-plated and equipped with air balls which makes paper-pushing easily and rusty-proof.Large side workingtable(1000*800) is optional. 3. IR photoelectric protection,buttons by two hands safety devices. 4. safety device for knife bed, overloading protection for cutting,automatic return safety device. 5. imported hydraulic components are adopted in hydraulic system,the pressure can be adjusted.The paper is pressed twice by pressure-increased system. 6. mechanical assistance device for knife replacement makes knife replaced quickly and safely. 7. optical knife alignment equipped makes cutting more convenient. 8. chrome-plated working table. 9. PLC control system. 10. ejecting device for knife bar. 11.flat worm speed reducer transmission. 12. inside electronic knife locker to make the cutting more safety and stable. 13. Multination langueage operation interface. 14.Carry on the block programming operation through the figures and diagrams operation manual.
XHYW Computerized Paper Cutters With Large Screen
Product Introduce: This model adopts japanese Mitsubishi AC digit servo control system,10.4inch colorful liquid crystal display screen of resolution rate 0.01mm,hasself-diagnostic function of troubles and displays the operating pattern,dynamic cutting display,running situation,dyna mic follow-up.The max paper-pushing speed is 5-18m/min,it adopts stronger computer operating system.The storage time canbe up to 300000 hours above .It has self maintenance to the operating system.ltaly hydraulic components, japan and korea electric com ponents.Taiwan ball lead screw and linear guide-rail are used.PLC controller can monitor all the electrical and mechanical section.Its key parts adopt imported bearing of low maintenance. Main Features: 1. Ball lead screw and linear guide-rail makes paper impeller run smooth,low noise,accurate positioning,enhance the cutting precision and speed greatly,prolong the service lift of paper cutter. 2. The working tables are all chrome-plated and equipped with air balls which makes paper-pushing easily and rusty-proof.Large side workingtable(1000*800) is optional. 3. IR photoelectric protection,buttons by two hands safety devices. 4. Safety device for knife bed, overloading protection for cutting,automatic return safety device. 5. Imported hydraulic components are adopted in hydraulic system,the pressure can be adjusted.The paper is pressed twice by pressure-increased system. 6. Mechanical assistance device for knife replacement makes knife replaced quickly and safely. 7. Optical knife alignment equipped makes cutting more convenient. 8. Chrome-plated working table. 9. PLC control system. 10.Ejecting device for knife bar. 11.Flat worm speed reducer transmission. 12.Inside electronic knife locker to make the cutting more safety and stable. Technical parameter:
Model |
920 |
1150 |
1300 |
1370 |
Cutting Width |
920mm |
1150mm |
1300mm |
1370mm |
Max. cutting height without assistance pressing plate |
120mm |
160mm |
130mm |
160mm |
Max. cutting depth |
1100mm |
1150mm |
1300mm |
1450mm |
Min. cutting depth without assistance pressing plate |
25mm |
30mm |
30mm |
30mm |
Extended length of working table |
650mm |
700mm |
730mm |
730mm |
Height of working table |
880mm |
880mm |
880mm |
880mm |
Machine width including side working table |
2180mm |
2380mm |
2630mm |
2700mm |
Total length of working table |
2150mm |
2220mm |
2420mm |
2750mm |
Cutting speed |
40times/min |
45 times/min |
45 times/min |
45 times/min |
Max. paper pressure |
35000N |
40000N |
40000N |
45000N |
Power of main motor |
3kw |
4 kw |
4 kw |
4 kw |
Motor for paper feeding |
0.37kw |
0.55 kw |
0.55 kw |
0.55 kw |
Air pump |
0.55kw |
0.75 kw |
0.75 kw |
0.75 kw |
Machine Weight |
2800kg |
4000kg |
4000kg |
4800kg |
Overall dimension(L*W*H) |
2280×1400×1850mm |
2500×1550×2100mm |
2600×1600×2000mm |
2880×1600×2100mm |
XHYK Computerized Pager Cutters
Product introduce: It is equipped with japanese Mitsubishi AC digital servo controlling technologe ang 5.7 inch display screen,the data resolubles and displays the operating patrern,100 program units,over 5000 different cutting positions ,it can memorize,store and dynamic follow-up.The max paper-pushing speed is 5-16m/min.It adopts ltaly hydraulic components,japan and korea electric components,Taiwan ball lead screw,linear guide-rail.PLC controller can monitor all the electrical and mechanical section.Its key parts adopt importsd bearing of low maintenance. Main features: 1. Ball lead screw and linear guide-rail makes paper impeller run smooth,low noise,accurate positioning,enhance the cutting precision and speed greatly,prolong the service lift of paper cutter. 2.The working tables are all chrome-plated and equipped with air balls which makes paper-pushing easily and rusty-proof.Large side workingtable(1000*800) is optional. 3.IR photoelectric protection,buttons by two hands safety devices. 4.Safety device for knife bed, overloading protection for cutting,automatic return safety device. 5.Imported hydraulic components are adopted in hydraulic system,the pressure can be adjusted.The paper is pressed twice by pressure-increased system. 6.Mechanical assistance device for knife replacement makes knife replaced quickly and safely. 7.Optical knife alignment equipped makes cutting more convenient. 8.Chrome-plated working table. 9.PLC control system. 10.Ejecting device for knife bar. 11.Flat worm speed reducer transmission. 12.Inside electronic knife locker to make the cutting more safety and stable. Technical parameter:
Model |
920 |
1150 |
1300 |
1370 |
Cutting Width |
920mm |
1150mm |
1300mm |
1370mm |
Max. cutting height without assistance pressing plate |
120mm |
160mm |
130mm |
160mm |
Max. cutting depth |
1100mm |
1150mm |
1300mm |
1450mm |
Min.? cutting depth without assistance pressing plate |
25mm |
30mm |
30mm |
30mm |
Extended length of working table |
650mm |
700mm |
730mm |
730mm |
Height of working table |
880mm |
880mm |
880mm |
880mm |
Machine width including side working table |
2180mm |
2380mm |
2630mm |
2700mm |
Total length of working table |
2150mm |
2220mm |
2420mm |
2750mm |
Cutting speed |
40times/min |
45 times/min |
45 times/min |
45 times/min |
Max. paper pressure |
35000N |
40000N |
40000N |
45000N |
Power of main motor |
3kw |
4 kw |
4 kw |
4 kw |
Motor for paper feeding |
0.37kw |
0.55 kw |
0.55 kw |
0.55 kw |
Air pump |
0.55kw |
0.75 kw |
0.75 kw |
0.75 kw |
Machine Weight |
2800kg |
4000kg |
4000kg |
4800kg |
Overall dimension(L*W*H) |
2280×1400×1850mm |
2500×1550×2100mm |
2600×1600×2000mm |
2880×1600×2100mm |
|